Jiangsu Degao Machinery Co., Ltd.　

Technology

Check category
Your position: Home
/
Technology
/
Maintenance

Regular inspection of granulators

First of all, particle machine check regularly. Changzhou yonghe fine chemical co., LTD., points out that particles machine must regularly check parts, to every month, check the worm gear, worm, lubrication on bolts, bearings and other activities whether some flexible rotation and wear situation, found that defects should be timely repair, shall not be used. Second, the pellet machine has exquisite placed. Machine should be placed in dry cleaning of indoor use, shall not be in the atmosphere contain acids and other places on the body of corrosive gas circulation use. Third, the pellet machine downtime issues. When particles machine or stop after using, rotating drum should be removed in cleaning and clearing the remaining FenZi inside bucket, and then set up, prepare for next time use. Occurred in the fourth, when drum work before and after the move, please adjust front bearing pawn M10 screws on to the appropriate location. If there are running of the gear shaft, please adjust bracket screw back to the appropriate location and adjust the clearance to the bearing noise does not occur, hand belt pulley, elastic appropriate advisable, too tight or too loose all can make the machine may be damaged. Fifth, such as stop using for a long time, the machine must be wipe and clean the whole body, parts of smooth surface coated with anti-rust oil, cloth canopy hood.
Click to see more
09
2016-09

The development of feed machinery in China

Time of issue: : 2016-09--09
At present, the widespread adoption of feed processing machinery, productivity is not high, such as domestic puffing machine maximum output of 3 tons ~ 5 tons/hour, has a certain gap compared with abroad. In terms of the development of feed processing machinery, the United States and Europe is ahead, stand-alone equipment automation and complete sets of equipment automatic control program is higher. Feed machinery industry in our country should be the direction of large-scale, intensive, by expanding sales to reduce the production cost and management cost, improve efficiency. Mill in China should further make a breakthrough on load control technology, and the central control technology combination, realize the grinder completely simulate the working state of each; Developed a safe and reliable automatic screen institutions change, make the mill in the case of non-stop automatic in screen, reduce downtime, facilitating the production of different materials, improve efficiency. Mixer mainly in discharge uniformity of detection, automatic detection of leakage, after mixing of automatic cleaning aspects to do further research, and to study particle machine conditioning time control technology for the material, such as the different material, conditioning automatically adjust Angle, change the residence time of a material on or through the conditioning implement automatic adjustment of the blade Angle to implement, etc.; To develop a dynamic automatic feeder roller pressure, ring die clearance adjusting mechanism, the particles on the access of feed material pulverization instrument equipment, and to achieve timely control, acceleration feedback speed, improve the quality of products. In today's China need to increase the investment in the enterprises, expand the basic research. From the point of feed machinery industrial development scale good countries, many famous feed machinery manufacturers, have their own research institutions or scientific research institutions and the relevant research of cooperation, the most advanced, most of the cutting edge of technology in the enterprise hands, they have a strong development momentum and competitive forces. As a result, China's feed machinery manufacturing enterprises to participate in international competition, must increase investment in scientific research, basic research for the development of frontier. Can adopt the method besides enterprise self-built research institutes, and the relevant scientific research institutions, colleges and universities, and even other relevant scientific research departments of industry is very necessary, also is feasible. Through this kind of a wide range of cooperation, take out the advanced product, enhance the competitiveness of the enterprises in the international market.
查看详情 查看详情
09
2016-09

Feed machinery roughly this several parts

Time of issue: : 2016-09--09
1、Base: play the role of the connecting parts and bearing mill, make them form a whole. Shredded material is being exhausted from the base. 2、Rotor: the main shaft, hammer frame plate, pin shaft, bearings and other parts, hammer, is the main moving parts of crusher. Rotor speed is higher, assembled on without pin and hammer into the dynamic balance test. 3、Operate the door: replace the sieve plate or hammer to open door operation. Crusher work by locks lock door operation, ensure the operation of rotor rotating door can't open on its own. 4、On the chassis: upper feeding mouth, lower connection with base, sieve plate on both sides respectively equipped, and the rotor of the crushing chamber, the material in crushing chamber to smash. 5、Feeding guide mechanism: make the material from the left or right into the crushing chamber. Feeding guide plate of the reversing manual control to ensure the feed direction consistent with the rotor turning. 6、Pressure screen structure: the locking device connected, ensure that screen piece fixed on the shredder. 7、Sieve sieve beam: sieve beam and pressure institutions together to screen piece fixed on the shredder. Production of feed mill adopts double rotor structure, greatly improve the working efficiency.
查看详情 查看详情
09
2016-09

Pellet feed is made of particles machine

Time of issue: : 2016-09--09
Particles is roughly divided into two kinds, flat die feed pellet machine and ring die pellet machine, see you every day how much is the production of pellet feed required, if lower productivity can choose 300 flat die pellet machine, if the required quantity is larger then choose ring die pellet machine, ring die is generally small and medium-sized farms and feed mills. Less than two tons of words every day you are advised to choose the flat die pellet machine. Compound feed is the most important material base, modern chicken is developed on the basis of modern science and technology, effectively promoted the development of the poultry industry in our country. Similarly, 3-yellow production has changed the traditional breeding way USES the compound feed, single feed make 3-yellow production level has greatly improved. Such as quality 3-yellow and local varieties of feed remuneration increased from 4.5-5 to 1 to 3, 4:1. Compound feed is according to the varieties and the growth days of age, the production performance aspects of requirements, standard according to nutrition and feed formula, will form the diet of chicken of various feed ingredients ground into powder, mix evenly into the feed. Compound feed according to its shape, can be divided into powder and pressed into feed of granular particles. According to its nutrition ingredient into perfect compound feed and compound feed, concentrated feed.
查看详情 查看详情
09
2016-09

The use of feed machinery and maintaining this is very important

Time of issue: : 2016-09--09
Equipment vibration fault     Feed factory most of the key equipment for rotating machinery, such as granulating machine, extrusion machine, mixer, crusher and its auxiliary fan, etc. Rotating equipment often violent vibration failures, and unable to work. Vibrations can be caused by many reasons, first, we should consider the bearing failure. Bearing defects can lead to severe shock, serious noise, and even cause equipment damage. Bearing according to the structure can be divided into rolling bearing and sliding bearing. Rolling bearing in the process of operation in case of improper assembly, poor lubrication, foreign bodies to enter and overload, and so on and so forth, are likely to be premature damage, mainly for wear and tear, damage to the cage, and outer ring fracture and plastic deformation, etc. Bearing clearance is when one side of bearing inner ring or outer ring fixed, the other party to do radial or axial movement of the mobile. Use the longer bearing, normal wear and tear, the greater the clearance is, the greater the equipment vibration will increase, the need to replace new bearing. For pelletizer, bearing clearance can be fixed on the spindle, the spindle bearing inner ring load up to check and measurement are added to the rotor. Bearing installation to master a principle, that is, can pass through the corresponding ring installation force or moment, usually adopt force fit, heating to install. In addition, the lubrication of the bearing is one of the important factors about its performance and lubricant and lubricating way appropriate or not will affect the service life of bearing. Through lubrication, can reduce the channel and the steel ball of rotary friction, sliding friction of ball and cage, cage and channel guide surface sliding friction, take away from heat and other external bearing internal friction heat, prevent bearing heating. The filling quantity of the grease with the shell structure and volume of different and different, generally filled to capacity of 1/3 to 1/2. But for low-speed bearing, so as to prevent the entry of foreign body, sometimes padding to 2/3 ~ 1. Second, we should consider the equipment vibration due to unbalanced rotor. The main cause of unbalanced rotor are: rotor scale, the counter weight loss, rotor deformation and the rotation center and the center of mass is not coincidence, this usually does not consider, equipment factory are made of dynamic balance). Finally, you need to check whether there is any loose on a foot, the equipment is installed in strict accordance with the specification, the connection is loose, the coupling gap (normally 2 ~ 3 mm), flatness, perpendicularity adjusting is appropriate. Equipment production is low Ring die pelletizer low yield factor A and bell ring die surface surface rolling, needs to be chamfer. B, ring die compression ratio improper selection. Selection principle: livestock and poultry feed 9 ~ 13; Fish feed 12 ~ 15; The shrimp feed 20 ~ 25; Heat-sensitive feed 5 ~ 9; The grasses and straw feed 6 ~ 9. C, die blocked. By the ring die tapping blockage in the outgoing hole, removal of impurities. D, ring die opening rate is too low, leading to lower productivity. Roller wear factor A and roller shell, need to change in time. B, a new ring die and old roller, roller and ring die will lead to the low yield. New ring die with roller shell should be adopted for granulating, the whole contact pressure roller and ring die clearance is consistent, to achieve uniform wear. Conditioning device blade factors influence material conditioning effect after blade wear, material mixing, steam absorption effect is poor. Conditioning implements material softening is bad, affect the particle pulverizing rate and yield. Tempering temperature factors Tempering temperature is too low. Suggested control in: livestock and poultry is expected to 70 ~ 88; Fish is 82 ~ 95; Shrimp is 90 ~ 105; Heat-sensitive feed 45 ~ 69. Unit: ℃. Steam quality factor points cylinder pressure should be ≧ 0.6 Mpa; The vapor pressure of 0.1 ~ 0.1 M working properly after decompression, to ensure that the steam for excluding the saturated steam condensed water. Mill production low A, check whether the material has been shattered section at A time. B, material is added in the secondary mixed oils. C, the formula of raw material whether to add the silkworm chrysalis. D, the guide plate and the host are consistent. E injection is normal, whether the electromagnetic valve, filter cloth is blocked. F, dust collector fan configuration errors, the fan to error. G, hammer sieve clearance is not appropriate, hammer badly worn. H, severe pressure sieve plate wear. I, sieving slice mode of hole is wrong, opening rate is too low. J, impeller feeder for the opening of the tuyere not open or inappropriate. K, raw material moisture content is too high. L, mesh aperture is not in conformity with the requirements, leading to excessive crush material. M, who did not use the origi
查看详情 查看详情
09
2016-09

The composition of automation equipment component

Time of issue: : 2016-09--09
Automation equipment most generally have the following parts: 1.Indicator light: general mostly are light-emitting diodes (leds), long life, neon bulb and bulb life is short, job is an alternating current and direct current voltage. 2.Button and urgent stop switch: button is often used in pneumatic and control keys, such as temporary, also some kinds of rotating button control; Scram button are usually red and yellow. 3.Fuse: mainly protection circuit, when the voltage and current is too large, can fuse protection circuit. 4.Switch and power switch: control buttons. 5.Circuit breaker: mainly is the restoration of short circuit protection, instantaneous short circuit occurs when the circuit and electric device and instantaneous large current, automatic trip, protection device for posterior. 6.Ac contactor: mainly used to control equipment of the main circuit of the power outages, general electric current is larger. To control power in contact. 7Intermediate relay, and have the same ac contactor is a function of the protection circuit. 8.Hot relay: thermal element, is mainly used for the protection of the equipment temperature, automatic short circuit protection at the back of the line. 9.Delay protection: general electric power delay and delay. 10.Knife switch: main artificial broken electronic control and control, generally speaking, there are two or three knife. 11.The leakage switch: mainly used for protection of personal safety, single-phase and three-phase residual current switch. Hope the above comments in you use, you are welcome to inquire.
查看详情 查看详情
Previous page
1
2

Copyright © 2021 Jiangsu Degao Machinery Co., Ltd.   苏ICP备11082151号  www.300.cn  Changzhou This site supports IPv6
Add: No.89, Kunlun North Road, Kunlun Economic Development Zone, Liyang City, Jiangsu Province　Tel:0519-87806006　Fax:0519-87806088　E-mail: cnjscxy@163.com

Copyright © 2021 Jiangsu Degao Machinery Co., Ltd. 
苏ICP备11082151号  www.300.cn  Changzhou This site supports IPv6